Atlantis Posted June 23, 2020 Share Posted June 23, 2020 Imprints on x3 needs fixing Some creatures are fine on x3. But some aren't possible (online w/lag). For example an Anky (and others with the same print time (lightpets, moschops, trike, daeodon, direwolf, saber, etc) needs two prints. However you only have 15minutes spare to do so. With lag this is often not possible. It needs some tweaking as we're gonna have more x3 breeding (x2 and x4 was never a problem btw). Link to comment Share on other sites More sharing options...
Fetzen Posted June 23, 2020 Share Posted June 23, 2020 U cant imprint otter to. Link to comment Share on other sites More sharing options...
Aylana314159 Posted June 23, 2020 Share Posted June 23, 2020 Easiest fix would be to remove the 3x since its leading to the conditions that make the servers lag. Link to comment Share on other sites More sharing options...
Volunteer Moderator GP Posted June 23, 2020 Volunteer Moderator Share Posted June 23, 2020 5 minutes ago, Aylana314159 said: Easiest fix would be to remove the 3x since its leading to the conditions that make the servers lag. They are attempting to improve that though. Link to comment Share on other sites More sharing options...
PreshusRoze Posted June 23, 2020 Share Posted June 23, 2020 5 hours ago, Fetzen said: U cant imprint otter to. Correct. Any dino - like the otter, (that on 1x takes less than 24 hours to raise from Birth) - will NEVER get an imprint on anything over 2x Breeding/Maturation. It's math. Every 8 hours there is an imprint. Divide the 21 hours+ ~3min by 3 (for 3x breeding/maturation speeds) and you get less than 8 hours. There is no way it'll reach imprint timer so you can imprint it. I learned that the hard way. It sucks. Wait till it's 2x before you attempt something like an otter again. Link to comment Share on other sites More sharing options...
Aylana314159 Posted June 23, 2020 Share Posted June 23, 2020 13 minutes ago, GP said: They are attempting to improve that though. It good that they are working on it. From what I have observed, people save lots of babies to raise during breeding events and put a lot of stress on the servers to do all those calculations. Link to comment Share on other sites More sharing options...
gamatron332 Posted June 23, 2020 Share Posted June 23, 2020 7 hours ago, Atlantis said: Imprints on x3 needs fixing Some creatures are fine on x3. But some aren't possible (online w/lag). For example an Anky (and others with the same print time (lightpets, moschops, trike, daeodon, direwolf, saber, etc) needs two prints. However you only have 15minutes spare to do so. With lag this is often not possible. It needs some tweaking as we're gonna have more x3 breeding (x2 and x4 was never a problem btw). Put imprint interval to 0.333333334 this will get you normal imprints on everything Link to comment Share on other sites More sharing options...
gamatron332 Posted June 23, 2020 Share Posted June 23, 2020 Just now, gamatron332 said: Put imprint interval to 0.333333334 this will get you normal imprints on everything Most people don’t know that if the mature rate is set higher that you then have to set imprint interval lower also. All you need too do is take how much faster you want it(in this case 3) and divide 1 by it 1/3=0.333333334 thus your imprint setting Link to comment Share on other sites More sharing options...
Fetzen Posted June 23, 2020 Share Posted June 23, 2020 I play on official x3 breeding is active so a otter is in 7hours full grown but imprint timer is 8hour! Link to comment Share on other sites More sharing options...
gamatron332 Posted June 23, 2020 Share Posted June 23, 2020 1 hour ago, Fetzen said: I play on official x3 breeding is active so a otter is in 7hours full grown but imprint timer is 8hour! Ah well Link to comment Share on other sites More sharing options...
Atlantis Posted June 24, 2020 Author Share Posted June 24, 2020 I don't mind it on creatures that take less time to raise than imprint timer on increased rates (like the otter). But it's way too tight on some creatures that you are able to print fully. However, a sidenote. Raising a Giga on x1 is impossible to get to 100%. As it goes from 9>11 and 79>81 (correct me on the 2nd one). You are always stuck with a 97% printed giga. Link to comment Share on other sites More sharing options...
Atlantis Posted June 24, 2020 Author Share Posted June 24, 2020 16 hours ago, gamatron332 said: Put imprint interval to 0.333333334 this will get you normal imprints on everything I can't as I'm on official though. But yeah a tiny adjustment would fix it. So like an anky would get 100% instead of 50% on x3. Link to comment Share on other sites More sharing options...
gamatron332 Posted June 24, 2020 Share Posted June 24, 2020 8 hours ago, Atlantis said: I can't as I'm on official though. But yeah a tiny adjustment would fix it. So like an anky would get 100% instead of 50% on x3. Yeah the imprints would be scaled to the growth time so that they would get normal imprints Link to comment Share on other sites More sharing options...
Atlantis Posted July 10, 2020 Author Share Posted July 10, 2020 - Added `BabyImprintAmountMultiplier` as an additional game.ini config for globally tuning imprinting. Is this a fix wildcard? If so, ❤️ Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.